Power & Control
O-Gauge - CAB-1L/Base-1L Command Set
Everything you need to start operating in the Lionel Command Control environment – and an economical way to add operators when running trains with friends! Whether you want to access the basic features of the LEGACY Control System or operate you older TrainMaster Command Control (TMCC) equipment, the CAB-1L remote controller allows you to walk around your layout while controlling your layout. The Base-1L receives signals from the remote and sends your commands across the layout. If you already have a #992 LEGACY Base (6-14295), you can simply add one or more CAB-1L remotes to your existing LEGACY layout. If you are looking to get started with the LEGACY Control System, these components are an affordable way to start unlocking many of Lionel's celebrated features. Only one Base-1L is required per layout, even if you use multiple remotes. Features Includes 6-37155 CAB-1L Remote Controller 6-37156 Base-1L CAB-1L Features Operates many LEGACY features and most TMCC equipment Operates LEGACY "Real-Time Quilling Whistle/Horn" feature in LEGACY Control System equipped locomotives Works with both the #992 LEGACY Base and the Base-1L (only one required per layout) Addresses 99 ENG (engine) and 99 TR (train) IDs Base-1L Features Only one required per layout, unless there is a #992 LEGACY Base already installed Simple one-wire connection to your layout Single serial-port for limited system expansion
2 in stock
O-Gauge - GW-180 Transformer
Introducing the ideal transformer for operating trains and accessories on expanding and medium-size layouts! From the Postwar-inspired styling of the controller, to the mighty PowerHouse power supply that provides a circuit breaker and on/off switch, this transformer has all the power you need, plus electronic overcurrent protection to help save your sensitive electronics in the event of a short circuit. Use the throttle lever to control speed and power. Operate your favorite features with the bell, whistle/horn, and direction buttons. Two outputs are available on the rear of the unit. A 0-18 volt variable AC output serves as you main track power source. The other programmable AC output is perfect for accessory operation from the same transformer. On the accessory output, simply set the accessory voltage to your desired level for continuous operation until you turn the unit off, completely independent of the train’s operation.
4 in stock
O-Gauge - IRV2 SENSOR ADD-ON
Add additional sensors to the IRV2 Sensor Module. The IRV2 includes 2 sensors, but can control up to 4!
Includes sensor board, cover, and cable.
Gauge: O Gauge
Most Recent Catalog: 2018 C1 Big Book
5 in stock
O-Gauge - LCS SENSORTRACK 2 (IRV2)
Allows for the addition of the LCS SensorTrack to a layout that does not use FasTrack.
Each module can control up to four (4) individual sensors.
Module includes two (2) sensors with cabling. Additional sensors available for separate sale.
Sensors include cover that attaches to existing track ties. Just drill a hole for the wire, mount the sensor between the rails, and you're good to go!
Gauge: O Gauge
Most Recent Catalog: 2018 C1 Big Book
3 in stock
O-Gauge - Legacy #990 Command Set
Here’s all you need to get started...
The #990 LEGACY Command Set
The #990 LEGACY Command Set features a #991 LEGACY CAB-2 Remote Controller and a #992 LEGACY Command Base/Charger, the two components you need to get started. Only one LEGACY Command Base/Charger is required per layout.
Like traditional TMCC, the LEGACY Command Base/Charger receives information from the Remote Controller and sends it out to the track via a simple one-wire connection. But that’s not all. The LEGACY Command Base/Charger remembers information about your layout, enabling the CAB-2 Remote Controller to display road names and numbers on the LCD screen.
#991 LEGACY CAB-2 Remote Controller
#992 LEGACY Command Base/Charger
CAB-2 Remote Controller Features:
Back-lit LCD screen - the largest on the market
Back-lit LCD keypad displays numbers or icons for ease of use
Built-in rechargeable batteries
Feedback mode - the remote vibrates to reinforce the effort and momentum of your locomotive
Accepts memory modules from each LEGACY Control System locomotive
COMMAND BASE/CHARGER FEATURES:
Only one LEGACY Command Base/Charger required per layout
Simple one-wire connection to your layout
Built-in dock for recharging CAB-2 Remote Controller
Stores operating information and settings for your layout
5 in stock
O-Gauge - Legacy #993 Expansion Set
Add additional remotes for your layout...
#993 LEGACY Expansion Set
Need additional remotes? The #993 LEGACY Expansion Set includes a #991 LEGACY CAB-2 Remote Controller and a #994 LEGACY Charger.
CHARGER BASE FEATURES:
2 in stock
O-Gauge - Legacy Powermaster
Lionel’s LEGACY PowerMaster provides superior AC track-voltage control for your command-equipped layout
Use it with any Lionel remote to remotely adjust track power from a Lionel PowerHouse or other external AC transformer (sold separately). Now, run conventional engines and fine-tune your command-equipped locomotives, lighting and accessories with precision. The LEGACY PowerMaster allows for 32, 120, or 200-speed step AC voltage control.
Lightning-fast over-current protection trips the PowerMaster’s internal breaker before those of the power transformer, safe-guarding your locomotive electronics and layout wiring. Then the PowerMaster lets you restore track power from your remote. Stop searching for tripped breakers hidden under your layout!
Features •Works with all Lionel Command Remotes
•Control conventional locomotives remotely; control speed, direction, whistle/horn, and bell
•Vary track power to fine-tune lighting, accessories, and command-equipped engines
•Remotely restore power after shorts
•Controls up to 180 watts of external power
•Receive commands wirelessly, no serial cable required
•Use one LEGACY PowerMaster per track loop to operate conventional locomotives independently
•Control one or more powered accessories as a group
•Split your yard into separate power blocks with additional LEGACY PowerMasters
1 in stock
O-Gauge - Legacy Writable Utility Module
We recommend purchasing separate Utility Modules for Base updates, CAB-2 updates, and system back-ups.
Features •Multi-purpose writable module
•LEGACY Base and CAB-2 operating system upgrades
•Ability to create custom engine modules
•Upgrade information available online
21 in stock
O-Gauge - LionChief - 72 Watt Power Supply (4 Amp)
LionChief 72-Watt Power Supply (4 Amp)
15 in stock
O-Gauge - TMCC Direct Lockon
Connect your PowerHouse Power Supply directly to the track with the TMCC Direct Lockon. Featuring a selectable current setting (for the 135-Watt or 180-Watt PowerHouses), the Direct Lockon eliminates the need for a PowerMaster if you run only TMCC- or LEGACY-equipped locomotives. For added safety, the Direct Lockon provides over-current protection and an automatic reset. It is compatible with both Lionel FasTrack and O/O27 track systems. includes power wire with FasTrack connectors and one standard Lionel Lockon.
14 in stock
O-Gauge - ZW-L Transformer
New and More Advanced Version of the Classic Lionel ZW
No single product has come to symbolize the legend of Lionel more than the Lionel ZW. That’s why we’re especially proud to announce a new and more advanced version – the Lionel ZW-L Transformer. True to the signature design elements of the original, the ZW-L is molded in phenolic resin and features the same distinctive four-handle operation as its predecessor. The ZW-L can run up to four trains or accessories at the same time on different layouts. The two engineer-type handles provide independent control of two variable voltage circuits, each with built-in whistle, direction, and bell controls. Two additional accessory circuits can be set by means of the dial-type controls to any desired voltage. The ZW-L Transformer is designed to give you smoother operation and more realistic control of your engines and accessories. Operation of the four handles now allows for fine control of up to 200 speed steps. It also provides a wider range of control at the minimum and maximum extensions of handle dial motion, and comes equipped with a smoother, more durable handle gearing system. Voltage and current from each of the four channels of the ZW-L Transformer are cleanly displayed in four easy-to-read, analog ammeter/voltmeter dials that are housed in the “dashboard” face. A full 620-watts of power are built inside the unit, so there’s no need for separate power bricks. To keep your Controller operating safely, the ZW-L also comes equipped with an automatic temperature controlled cooling fan, a circuit breaker for each channel output, and an on/ off switch on the front. Additionally, LIONEL letters light up in blue on the front face of the unit when the ZW-L is turned on. Whether you run vintage or state of the art locomotives and accessories, the new Lionel ZW-L Transformer provides more realistic conventional control of your layout operations than ever before!
4 in stock